Nikon HT1000 Bedienungsanleitung PDF herunterladen (Seite 8)

E-8

PC CONTROL

RGB IN

DVI-D IN

SC TRIGGER

VIDEO IN S-VIDEO IN

S-VIDEOS-VIDEO RGB/DVIRGB/DVIVIDEOVIDEO AUDIO INAUDIO IN

COMPONENT

Y Cb/Pb Cr/Pr

93511

24110 86

71213

Terminal Panel Features

1. RGB IN / Component Input Connector (Mini D-Sub 15 Pin)

Connect your computer or other analog RGB equipment such as IBM

compatible or Macintosh computers. Use the supplied RGB cable to

connect to your computer. This also serves as a component input

connector that allows you to connect a component video output of

component equipment such as a DVD player. This connector also

supports SCART output signal. See page E-16 for more details.

2. DVI-D IN (DVI 24 Pin)

This connector can be used to accept digital signal output from a

computer or a setup box with a DVI connector. (HDCP compatible)

3. RGB/DVI AUDIO IN Mini Jack (Stereo Mini)

This is where you connect audio output from your computer con-

nected to RGB IN or DVI-D IN.

4. COMPONENT (Y, Cb/Pb, Cr/Pr) input Connectors (RCA)

Connect component video outputs (Y/Cb/Cr, Y/Pb/Pr) of the external

equipment such as DVD player.

NOTE: These connectors accept component signal only.

5. COMPONENT AUDIO IN Mini Jack (Stereo Mini)

This is where you connect audio output from your DVD player or

component equipment connected to COMPONENT IN.

6. VIDEO IN (RCA)

Connect a VCR, DVD player or laser disc player here to project video.

7. VIDEO AUDIO IN Mini Jack (Stereo Mini)

This is where you connect audio output from your VCR, DVD player

or laser disc player connected to VIDEO IN.

8. S-VIDEO IN (Mini DIN 4 Pin)

Connect a VCR, DVD player or laser disc player with S-Video output.

NOTE: S-Video provides more vivid color and higher resolution than the tra-

ditional composite video format.

9. S-VIDEO AUDIO IN Mini Jack (Stereo Mini)

This is where you connect audio output from your VCR, DVD player

or laser disc player connected to S-VIDEO IN.

10. PC CONTROL Port (Mini DIN 8 Pin)

Use this port to connect your PC to control your projector via a serial

cable. This enables you to use your PC and serial communication

protocol to control the projector. The NEC optional serial cable

(CA03D) is required to use this port. If you are writing your own pro-

gram, typical PC control codes are on page E-56. A cap is put on the

port at the factory. Remove the cap when using the port.

11. SC TRIGGER Mini Jack

When the projector is powered ON the screen trigger output sends a

high voltage trigger to the screen controller and the screen will go

down.

When the projector is powered OFF the screen trigger stops sending

a low voltage trigger to the screen controller and the screen will go

up.

NOTE: To enable the SC.TRIGGER function, be sure to turn on "Screen Trig-

ger" in "Page 4" of the Setup. See page E-42.

NOTE: Screen Controllers are supplied and supported by screen manufac-

tures. This option is not included with the projector.

NOTE: Do not use this jack for anything other than intended use. Connecting

an audio cable or equivalent to the SC. TRIGGER Mini Jack causes damage to

this mini jack.

12. PC CARD Eject Button

Press to eject a PC card partially.

13. PC CARD Slot

Insert a PC card or commercially available wired LAN card here.

Stereo mini cable

(not supplied)

Tip (12V)

Ring (NC)

Sleave (ground. 0V)

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 60 61

Kommentare zu diesen Handbüchern

Keine Kommentare

Nikon HT1000 Bedienungsanleitung Seite 8

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Projektoren Nikon HT1000