Nikon UPS Bedienungsanleitung

UPS/400 Installation and Administration Guide TABLE OF CONTENTS PAGE INTRODUCTION ………………………………………………………………… INTRO INSTALLATION/REINSTALLATION IN

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 10 SYSTEM ATTRIBUTES SCREEN

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 11 SYSTEM ATTRIBUTES (TEST MODE) Test mode of UPS/400 is turned on or off from the UPS

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 12 SYSTEM ATTRIBUTES SCREEN (TEST MODE)

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 13 AN EXAMPLE The following narrative describes an example of the functions performed

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 14 SYSTEM ATTRIBUTES SCREEN (EXAMPLE – SYSTEM DEFAULTS) These values will be used wher

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 15 REMOTE SYSTEMS MAINTENANCE (NETWORKING) The Remote Systems Maintenance screen allo

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 16 UPS/400 NETWORK SUPPORT Note: The sensor cable from the UPS may be connected

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 17 WORK WITH MONITOR STATUS The Work with Active Jobs display shows the performance an

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 18• The subsystem can be interrupted while the job is in this state by other requests

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 19• Open file information • File override information • Commitment control status •

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 2 INTRODUCTION UPS/400 is power monitoring software that continuously monitors your UP

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 20• EVK: Started by a procedure start request • INT: Interactive • MRT: Multiple

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 21 • BSCW: The job is waiting for the completion of an I/O operation to a binary synch

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 22• SELW: This job is in a select wait. More information on the select() function is

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 23 DELIVERY: The

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 24• Recharge rate: Rate of recharge as defined in the System Setup screen. This valu

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 25 SYSTEM SETUP This menu allows setting of values that are global in nature to the op

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 26 TO MAKE UPS/400 PERMANENT To make UPS/400 permanent, the user should complete and r

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 27 PRODUCT WARRANTY AND SUPPORT This section contains important warranty and product s

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 28 REMOTE CUSTOMER SUPPORT Automated Customer Support (ACS) is designed to permit remo

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 29procedure – and off at the end. You must insure that there are no other lines varied

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 3 Stage 4: System Restore and Follow-up Monitoring • If power is returned, all acti

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 4INSTALLATION/REINSTALLATION INSTRUCTIONS If you are installing UPS/400 for the first

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 5 Internet Download Installation 1. At the AS/400 command prompt, type: CRTLIB UPSTRI

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 6 GETTING STARTED Use the command STRUPS400 to start UPS/400. This will transfer y

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 7 MAIN MENU This is the main menu for UPS/400 that provides access to all other syste

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 8 SYSTEM ATTRIBUTES The System Attributes display is used to identify the system para

UPS/400 . . . an IBM AS/400 UPS power monitoring system . . . 9user program will be ended when the power down occurs. NOTE: There is no exit proced