Nikon DLP 837 Series Bedienungsanleitung PDF herunterladen (Seite 53)

6. NetCommand Control of an A/V Receiver (837 Series) 53

Automatic Au

dio or Audio/Video Switching

The following setups enable the A/V receiver to switch

automatically to the correct input when you select a

device in the TV’s Activity menu.

Three different connection arrangements are described

here. Review the descriptions to find the setup needed

for your equipment.

To hear digital surround sound from a source device

you must use the setup described for Case 2

To set up control of an A/V receiver you need:

The remote controls for the TV and A/V receiver.•

An IR emitter cable available from Mitsubishi.•

Connecting cables•

IMPORTANT

All audio from what you are watching on the TV is

always available from both the TV’s AVR AUDIO

OUTPUT and DIGITAL AUDIO OUTPUT jacks.

To use the digital surround sound capabilities of

your A/V receiver however, you must connect the

audio output from your DVD player, satellite receiver,

or cable box directly to the A/V receiver.

Before You Begin

Connect your A/V devices to the TV and connect

your A/V receiver to the audio outputs on the TV

and the DVD player. Note the name of the device

connected to each A/V receiver input. See initial

setup, page 10 , and “TV Connections,” page 14 .

Position Net Command IR emitters as described in

“IR Emitter Placement,” page 46 .

Set the TV’s remote control to

mode using the

side button.

Open the

Inputs > AVR menu, highlight NEXT

and press

ENTER

to display the device-key-learning

menu.

Case 1: Automatic A/V Rec eiver

Switching to the TV Audio Input

Most devices are set up to use the TV’s audio output like

the VCR in this example; analog audio from the device is

sent through the TV to the A/V receiver’s TV audio input.

Use this setup for:

Audio Available from TV only. • Send audio from

the

ANT

input to the A/V receiver from the TV’s

analog or digital audio output.

Use this setup to make the A/V receiver switch to its

designated TV audio input when viewing programming

from the

ANT

input.

Setting Up A/V Receiver Control, continued

Analog Stereo Audio. •

Audio from sources with only

analog stereo output (such as a VCR) can be sent either

directly to the A/V receiver or through the TV first.

Mitsubishi recommends you send audio through the

TV as shown in the example. The TV converts analog

audio to digital format to send to a digital A/V receiver.

HDMI Digital Stereo Audio. • Digital stereo audio

from an HDMI connection is available both in digital

and analog format from the TV’s analog and digital

audio output jacks.

audio + video

Incoming Coaxial Cable

to TV’s ANT input

A/V Receiver

DVD audio

input

TV audio input

TV audio

out

audio output from

TV (digital or analog)

video

analog audio

VCR with

Analog Audio Output

Important:

To use this setup, you must connect the TV’s

audio output to the A/V receiver’s TV audio input jack.

In the

Inputs > AVR menu, press to highlight

TV audio out as the A/V receiver input to control.

Press

ENTER

on the TV’s remote control.

While the text

TV audio out is flashing, press and

hold the

TV INPUT

key on the A/V receiver’s remote

control.

When a check appears next to

TV audio out,

release the

TV INPUT

key.

If the text stops flashing before the check mark •

appears, repeat this step.

To erase the IR code just “learned,” press •

CANCEL

while the name is highlighted.

Press

if finished or continue with Case 2 setup

for another audio source.

Case 1: Net Command setup for controlling A/V

receiver switching to the A/V receiver’s audio input from

the TV

The list displayed represents inputs in use. The

device names are those you assigned during Auto Input

Sensing or in the Inputs > Name menu..

1 2 ... 48 49 50 51 52 53 54 55 56 57 58 ... 85 86

Kommentare zu diesen Handbüchern

Keine Kommentare

Nikon DLP 837 Series Bedienungsanleitung Seite 53

Kommentare zu diesen Handbüchern