- 1 -Reference Manual35mm Film ScannerLS-2000ContentsCautionsSafety PrecautionsIf You Notice Anything AbnormalInstallation and StorageOverviewParts an
- 10 -Safety Precautions• the scanner may be subject to excessive vibration or physicalshockNote that the scanner contains glass parts; if the scanner
- 11 -Notice concerning prohibition of copying orreproductionNote that simply being in possession of material which has beencopied or reproduced by me
- 12 -OverviewOverviewThank you for your purchase of a Nikon LS-2000 scanner for35 mm and IX240 film. The LS-2000 film scanner offers highspeed and h
- 13 -Parts and Accessories: What’s in the BoxParts and AccessoriesThis chapter introduces the parts of the LS-2000 and lists theitems packaged with
- 14 -Parts and Accessories: OptionsOptional AccessoriesAt the time of writing, the following optional adapters wereavailable for the LS-2000.IA-20 a
- 15 -Parts and Accessories: PartsParts of the LS-2000Poweron/offswitchVentsMADE IN JAPAN100098SCSI SCSISCSI NBTERMINATOROFF ON65432107100–240V~0.3–0
- 16 -Parts and Accessories: Status LEDStatus LEDThe scanner’s status is shown by the LED on the front panel.When the status LED is on and glowing st
- 17 -SetupSetupThis chapter explains how to set up your scanner and connectit to a computer. Before using your scanner, you will need tocomplete the
- 18 -Setup: InstallationThe scanner has feet both on its base and on one side, makingit possible to place the scanner either on its base or on its s
- 19 -Setup: InstallationWhen using the optional SF-200 slide feederOnce the scanner is installed, slide the front cover open. Usinga coin, remove t
- 2 -ContentsMaintenanceCleaningStorageTransportTroubleshootingSpecifications
- 20 -Setup: Connecting the Power CableConnecting the Power CableBefore connecting the power cable, confirm that the scanner isoff and that the trans
- 21 -Setup: Connecting the SCSI CableConnecting the SCSI CableCommunication between your computer and the LS-2000relies on the Small Computer System
- 22 -Setup: Connecting the SCSI CableSCSI devices are connected to the computer in a “daisy chain.”Up to eight devices, including the computer and a
- 23 -Setup: Connecting the SCSI CableSCSI devices cannot be connected while the power is on.Before connecting the scanner to the SCSI chain, be sure
- 24 -Setup: Connecting the SCSI CableConnect a second SCSI cable to the other of the two connec-tors on the rear of the scanner, then connect the ot
- 25 -Setup: Connecting the SCSI Cable✔SCSI Connection Checklist• Turn off the computer, the LS-2000, and all SCSI devicesbefore connecting the scann
- 26 -Setup: Setting the SCSI IDTo change the scanner’s ID, turn the scanner off. Then, using ascrewdriver, turn the dial on the back of the scanner
- 27 -Using the Scanner: Turning the Scanner OnUsing the ScannerThis chapter covers basic scanner operations, from turning thescanner on to replacing
- 28 -Using the Scanner: Inserting and Removing Adapters✔Cautions• Wait until the status LED glows steadily or the scanner is offbefore inserting or
- 29 -Using the Scanner: Using the MA-20 SLIDE MOUNT ADAPTERWhen the scanner is installed on its side, insert the slides withthe base up and the shor
- 3 -CautionsCautions• The reproduction of this manual in whole or in part is pro-hibited save in cases in which Nikon’s prior permission hasbeen obta
- 30 -Using the Scanner: Using the MA-20 SLIDE MOUNT ADAPTERLandscape (wide) slideDo not insert slides with the longer side of the aperture facingthe
- 31 -Using the Scanner: Using the MA-20 SLIDE MOUNT ADAPTERSlides can be removed from the scanner by pressing the ejectbutton to eject the slide fro
- 32 -Using the Scanner: Using the MA-20 SLIDE MOUNT ADAPTERUsing the FH-2 to scan strip-filmThe SA-20 STRIP FILM ADAPTER is provided to scan 35 mm f
- 33 -Using the Scanner: Using the MA-20 SLIDE MOUNT ADAPTERStep 3—Close the FH-2Close the FH-2, keeping the ends of the black lower and upperholders
- 34 -Using the Scanner: Using the MA-20 SLIDE MOUNT ADAPTERSlide the film holder into the slide adapter until the holdertouches the back of the film
- 35 -Using the Scanner: Using the SA-20 STRIP FILM ADAPTERUsing the SA-20 STRIP FILM ADAPTER35 mm film-strips of from two to six frames in length ca
- 36 -Using the Scanner: Using the SA-20 STRIP FILM ADAPTERInserting filmTo scan a film strip, grasp the film gently by the sides and slidethe it int
- 37 -Using the Scanner: Using the SA-20 STRIP FILM ADAPTER✔Cautions• Do not attempt to insert film while scanning is in progress.• Do not remove the
- 38 -Using the Scanner: Using the SA-20 STRIP FILM ADAPTERStep 3—Remove the filmThe jammed film will be visible in the feed mechanism at therear of
- 39 -Using the Scanner: Using the SA-20 STRIP FILM ADAPTERCleaning the strip-film adapterIt is strongly recommended that you clean the SA-20 periodi
- 4 -CautionsFederal Communications Commission (FCC)Radio Frequency Interference StatementThis equipment has been tested and found to comply with thel
- 40 -Using the Scanner: Using the IX240 Film AdapterInserting filmIX240 film must be developed before it can be scanned. Todetermine whether a roll
- 41 -Using the Scanner: Using the IX240 Film Adapter✔Cautions•The latch button will lock when film is fed from the cartridgeinto the scanner. Do no
- 42 -Using the Scanner: Using the SF-200 Slide FeederConnecting the SF-200 to the scannerThe scanner must be on its base before the SF-200 can beins
- 43 -Using the Scanner: Using the SF-200 Slide FeederLoading the feederSlides to be scanned are inserted in the feed magazine. To loadthe magazine,
- 44 -Using the Scanner: Using the SF-200 Slide Feeder✔Cautions• Slides must be from 1.0 mm to 3.2 mm thick.• Mounts with rough surfaces could cause
- 45 -Using the Scanner: Using the SF-200 Slide FeederRemoving slidesSlides will be sent to the ejection magazine after scanning. Toremove slides fr
- 46 -Using the Scanner: Using the SF-200 Slide FeederClick the double right-arrow button in the attachment utility tomove the feed mechanism to wher
- 47 -Using the Scanner: Using the SF-200 Slide FeederTo use the attachment utility, open the Utility folder in thefolder to which you installed Niko
- 48 -Using the Scanner: Turning the Scanner OffTurning the Scanner OffTo turn the scanner off, end scanning operations and turn offthe computer. Wa
- 49 -Maintenance: CleaningMaintenanceThis chapter describes how to clean, store, and transport theLS-2000.CleaningBefore cleaning the scanner, turn
- 5 -Safety PrecautionsSafety PrecautionsObserve the following safety precautions when installing andoperating the LS-2000:• Do not allow your fingers
- 50 -Maintenance: TransportTransportThe LS-2000 is for use only in the country of sale. Nikon willnot be held responsible for consequences resultin
- 51 -TroubleshootingTroubleshootingIf you should encounter problems with your scanner, check thefollowing before contacting your retailer or Nikon re
- 52 -Troubleshooting• If you are using an IBM PC/AT compatible computer, hasyour SCSI board or PCMCIA card been tested and approvedby Nikon?A list of
- 53 -TroubleshootingProblem: a “no adapter in device” error appearsIf the software displays a “no adapter in device” error when youattempt to scan,
- 54 -SpecificationsSpecificationsLS-2000Film: 35 mm filmPositive and negative film, both color andmonochrome, may be used. Film may bemounted as 35
- 55 -SpecificationsSA-20 STRIP FILM ADAPTERFilm: 35 mm film strips of two to six frames (filmmust be flat or curl towards the emulsionsurface not mor
- 56 -EC DECLARATION OF CONFORMITYWeName: Nikon Europe BVAddress:Schipholweg 321, 1171 PL Badhoevedorp, The Netherlandsdeclare that the productProduct
- 6 -Safety Precautions• When handling the power and SCSI cablesUnplug the power cable by pulling on the plug, not on thecable itself. Pulling direct
- 7 -Safety Precautions• Do not disassembleThe interior of the scanner contains areas of high voltage.Removing the scanner’s cover could result in fir
- 8 -Safety Precautions• Keep cleanUse a dry cloth to remove any dirt from metal sections ofthe scanner and their surroundings. Using the equipmentwh
- 9 -Safety PrecautionsInstallation and StorageTo prevent fire or malfunction, follow the precautions givenbelow when operating or storing the scanner
Kommentare zu diesen Handbüchern