Nikon RADIUS CM200 Bedienungsanleitung Seite 26
- Seite / 70
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
2-12 MAINTENANCE
7.0 Radio Assembly
7.1 Chassis Assembly (for Low Power Models)
1. Ensure that the Fuji Poly Thermal Pad is on the small pedestal located on the PA
compartment of the chassis.
2. Verify that the potentiometer is soldered properly.
3. Take the main PCB and smear thermal paste on LDMOS Power Amplifier, TO220, and Audio
Power Amplifier.
4. Slide the main board diagonally into the chassis.
5. Tighten all eight screws (Torx T10).
6. Assemble the O-ring on the RF connector and tighten it using Torque 22 lb.in.
7. Tighten the RF connector security screw M2 using Torque 1.5 lb. (through the opening in the
PCB).
8. Take the Power Amplifier Clip and insert the leg-shape side into the opening groove located
on the PCB. Tighten the screw using Torque 13 lb.in
9. Take the PA Shield and place it on the PA compartment. Tighten the three screws using
Torque 13 lb.in. Tighten the middle screw first, then the screw located on the left side, and
lastly the screw located on the right side.
10. Insert the DC cable into the slot. Ensure that it is seated correctly on the chassis hook located
below the DC cable. Attach it to the chassis and PCB by tightening the two screws using
Torque 13 lb.in (Torx T10).
11. Take the main shield and place it on the chassis. Check that the corners of the main shield
are seated properly on the corner supports.
12. Take the main seal and place it inside the top cover. Verify that the main seal is seated prop-
erly on its placement ribs and all around the groove.
13. Take the upper cover, place it properly on the chassis, and push it down. Three click sounds
are heard from both sides and back.
7.2 Chassis Assembly (for High Power Models)
1. Verify that the potentiometer is soldered properly.
2. Take the main PCB and smear thermal paste on T0220 and Audio Power Amplifier.
3. Slide the main board diagonally into the chassis.
4. Tighten all eight screws (Torx T10).
5. Assemble the O-ring on the RF connector and tighten it using Torque 22 lb.in.
6. Tighten the RF connector security screw M2 using Torque 1.5 lb. (through the opening in the
PCB).
7. Take two PA Screws and place in screw holes over PA. Tighten the screws using Torque 13
lb.in.
8. Take the PA Shield and place it on the PA compartment. Tighten the three screws using
Torque 13 lb.in. Tighten the middle screw first, then the screw located on the left side, and
lastly the screw located on the right side.
9. Insert the DC cable into the slot. Ensure that it is seated correctly on the chassis hook located
below the DC cable. Attach it to the chassis and PCB by tightening the two screws using
Torque 13 lb.in. (Torx T10).
- Radius CM200 1
- & Motorola PM400 1
- CM200/CM300/PM400 3
- Foreword 4
- Computer Software Copyrights 4
- Document Copyrights 4
- Disclaimer 4
- Table of Contents 5
- Chapter 5 POWER UP SELF-TEST 6
- SAFETY INFORMATION 9
- Chapter 1 11
- INTRODUCTION 11
- 3.2 Motorola Online 12
- 3.3 Mail Orders 12
- 3.4 Telephone Orders 12
- 3.5 Fax Orders 12
- 4.0 Radio Model Information 13
- 1-4 INTRODUCTION 14
- Chapter 2 15
- MAINTENANCE 15
- 6.1 Control Head Removal 18
- Figure 2-3 Flat Cable Removal 19
- Main PCB Connector 19
- 6.2 Top Cover Removal 20
- 6.3 Main Shield Removal 21
- 2-8 MAINTENANCE 22
- 2-10 MAINTENANCE 24
- Control Head Housing 24
- Keypad Assembly 24
- 7.0 Radio Assembly 26
- 7.3 Control Heads Assembly 27
- 7.4 Control Head Fitting 27
- 7.5 Option Board Installation 28
- 8.3 Control Head - CM200 31
- 9.0 Service Aids 33
- 10.0 Test Equipment 34
- FLO830308-0 35
- FLO830307-0 35
- 12.0 Adapter Cable - FKN8113_ 36
- Chapter 3 37
- 3.0 RF Test Mode 38
- RF Test Mode 3-3 39
- RF Test Mode 3-5 41
- Chapter 4 43
- RADIO TUNING AND PROGRAMMING 43
- 7.0 Radio Tuning Setup 46
- Chapter 5 47
- POWER UP SELF-TEST 47
- 5-2 POWER UP SELF-TEST 48
- Chapter 6 49
- 1.2 Audio 50
- 1.3 Alarms and Accessories 50
- 1.4 Control Station 51
- 1.5 Public Address 51
- 1.6 Cables 51
- 1.7 Mounting 51
- 1.9 Peripherals 52
- Pin Function Description 53
- Chapter 7 55
- VHF2, 1-25 W, 146-174 MHz 55
- UHF2, 1-25 W, 438-470 MHz 56
- 1.3 Specifications 57
- Transmitter 58
- Receiver 58
- VHF1, 25-45 W, 136-162 MHz 59
- VHF2, 25-45 W, 146-174 MHz 59
- UHF2, 25-40 W, 438-470 MHz 60
- UHF3, 25-40 W 465-495 MHz 61
- 2.5 Specifications 62
- 3.0 MIL Standards 64
- GLOSSARY 65
- Glossary of Terms 65
- G-ii Glossary 66
- Glossary G-iii 67
- G-iv Glossary 68
Verwandte Produkte und Handbücher für Radio Stationen Nikon RADIUS CM200
(2 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 3.798 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern