Nikon HT1000 Bedienungsanleitung PDF herunterladen (Seite 42)

E-42

Enabling Power Management [Power Management]:

When this option is on and there is no input for five minutes or more,

the projector will automatically turn itself off.

Enabling Power Off Confirmation [Power Off Confirmation]:

This option determines whether a confirmation dialog for turning off

the projector will appear or not.

Enabling Horizontal and Vertical Keystone Correction Save

[3D Reform Save]:

This option enables you to save your current 3D Reform settings.

Saving your change once affects all sources. The changes are saved

when you turn off the projector.

Enabling High Speed Fan Mode [High Speed Fan Mode]:

This option allows you to select two modes for fan speed:high-speed

mode and normal speed mode.

When you wish to cool down the temperature inside the projector

quickly, check this box.

NOTE: Enable High Speed Fan mode if you continue to use the projector for

consecutive days.

Enabling Idle Mode [Idle Mode]:

The projector has two standby modes: Standby and Idle.

Standby is the mode that allows you to put the projector in the standby

condition which consumes less power than the idle mode. The pro-

jector is preset for Standby at the factory.

NOTE: The HTTP server functions are not available during Standby mode.

Enabling Screen Trigger [Screen Trigger]:

When "Screen Trigger" is selected and the projector is powered ON,

the screen trigger output sends a low voltage trigger to the screen

controller and the screen will go down. When the projector is pow-

ered OFF the screen trigger stops sending a low voltage trigger to

the screen controller and the screen will go up. Use a commercially

available stereo mini cable.

Enabling 3D Surround [3D Surround]:

Tu rn on or off the 3D surround effect.

After turn on this option, select "OK".

Clearing Lamp Hour Meter [Clear Lamp Hour Meter]:

Resets the lamp clock back to zero. Pressing this button appears a

confirmation dialog box. To reset the lamp usage hour, press "OK".

NOTE: The projector will turn off and go into standby mode after 1600 hours

(up to 2100 hours in Eco mode) of service. In this condition you cannot clear

the lamp hour meter on the menu. If this happens, press the "Help" button on

the remote control for ten seconds to reset the lamp clock back to zero. Do

this only after replacing the lamp.

[Page 5]

Selecting Communication Speed [Communication Speed]:

This feature sets the baud rate of the PC Control port (Mini DIN 8

Pin). It supports data rates from 4800 to 38400 bps.

The default is 38400 bps. Select the appropriate baud rate for your

equipment to be connected (depending on the equipment, a lower

baud rate may be recommended for long cable runs).

Selecting Default Source [Default Source Select]:

You can set the projector to default to any one of its inputs each time

the projector is turned on.

Last ................ Sets the projector to default to the previous or last

active input each time the projector is turned on.

Auto ............... Searches for an active source in order of Video →

S-Video → Component → RGB → DVI (DIGITAL) →

Viewer → Video and displays the first found source.

Select ............. Displays the selected source input every time the pro-

jector is started up. Select an input from the pull-down

menu.

Disabling the Cabinet Buttons [Control Panel Key Lock]:

This option turns on or off the Control Panel Key Lock function.

NOTE:

*This Control Panel Key Lock does not affect the remote control and the PC

Control functions.

* When the cabinet buttons are disabled, pressing and holding the CANCEL

button for about 10 seconds will change the setting to enabled.

1 2 ... 37 38 39 40 41 42 43 44 45 46 47 ... 60 61

Kommentare zu diesen Handbüchern

Keine Kommentare

Nikon HT1000 Bedienungsanleitung Seite 42

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Projektoren Nikon HT1000