Nikon COOLSHOT Bedienungsanleitung Seite 7

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 139
  • Inhaltsverzeichnis
  • FEHLERBEHEBUNG
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 6
12 13
Jp
En
Fr
Es
Pt
Ru
Se
Nl
De
It
Dk
Pl
Hu
Cz
Fi
No
Ro
Jp
En
Fr
Es
Pt
Ru
Se
Nl
De
It
Dk
Pl
Hu
Cz
Fi
No
Ro
操作方法
注意─ここに規定した以外の手順による制御や調整は、
危険なレーザー放射の被ばくをもたらします。
1.準備
リチウム電池 (CR2) を電池室に装填します。
([ 電池交換 ] の項参照)
2.視度調整
使用者の視度に合わせて、接眼内の LCD 表示がはっき
り見えるよう調整します。視度調整リングを反時計回
りに一杯まで回します。次に、電源をオンにして LCD
表示を点灯させ、接眼部を覗きながら視度調整リング
を時計回りに回し、LCD 表示がはっきり見える位置で
止めます。回しすぎたときは、視度調整リングを反時
計回りに大きく回して調整をやりなおしてください
調整が不十分ですと、目標物を正確に照準できないこ
とがあります。
3.測定
測定を始める前に、表示単位の設定を確認してくださ
い。
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
①POWER ボタン
を押します。
②照準をします。
電源オン直後
(イニシャライズ)
スタンバイ状態 照準中
③POWER ボタンを一度押します。8秒間の連続測定を開
始します。(単発測定はありません。
測定中
④8秒間、内部表示が「測定の可否」「目標までの距離」を表
示するために変化します。(レーザー照準マークは点滅)
測定不能・失敗 測定値表示
(目標1)
測定値表示
(目標 2)
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
⑤連続測定終了後、最終測定の結果(測定距離)が8秒間表
示され、電源オフになります。
電源オンの間(内部表示点灯中)に、POWER ボタンを押
すと、再度8秒間の連続測定を開始します。
ゴルフでグリーンのピンフラッグを測定するときは、測定中に
ピンフラッグをスキャンすると、測定が簡単に行えます。ピン
フラッグとの間に何も無い場合は、一番近い距離がピンフラッ
グまでの距離となります。
4.距離表示単位の選択( 出荷時の設定はヤードです。
1.内部表示 (LCD) が点灯していることを確認します。
2.MODE ボタンを押します。(2 秒以上 )
3.表示単位が替わったら、MODE ボタンから指を離しま
す。
4.設定後の表示は、その単位に換算されて表示されます。
メートル [
]ヤード [ ]
6. 電池交換時期
電池マークの表示『
』が点滅したときは、電池の容量
が低下しています。
電池の交換をしてください。[電池交換]の項参照)
7.視野照明のオン・オフ
暗くて液晶表示が確認できないとき、使用してください。
電源オン状態で MODE ボタンを短時間(2 秒未満)押すこ
とにより、視野照明のオン・オフが行えます。電源のオフで
も視野照明はオフになります。
なお、電源を再度オンにした時は、視野照明はオフ状態です。
5. 距離表示システム
COOLSHOT は、近距離優先距離表示システムを採用してい
ます。このシステムは、1回の測定で複数の測定値が得られた
とき、最も近い距離を表示します。
たとえば、立木の後ろに家があるとき、その設定結果(内部デー
タ)が
3 個の数値を得た場合、COOLSHOT では 115m(立ち木)
を表示します。ゴルフ等の用途に有用です。
立ち木 フェンス
距離データ 115m 123m 128m
Seitenansicht 6
1 2 3 4 5 6 7 8 9 10 11 12 ... 138 139

Kommentare zu diesen Handbüchern

Keine Kommentare