Nikon Laser IRT Bedienungsanleitung PDF herunterladen (Seite 2)

Operational Summary

Riflescope

1. Diopter adjustment

盧Look through the eyepiece with your eye positioned about 4 inches away from the eyepiece lens (Fig. 9), and you will see the Nikoplex reti-

cle (Fig. 10), or the BDC reticle (Fig. 11).

Be sure your eye is positioned within progper alinment and proper eye relief otherwise the view will "black out".

盪Point the objective end of the scope at the sky (Do not point at the sun) or at a plain unpatterned wall.

Turn the eyepiece adjustment counter-clockwise and then turn it clockwise until the reticle appears sharp.

2. Magnification

蘆The Laser IRT 4-12X42 has a variable magnification from 4 to 12X.

To change powers. just rotate the power selector ring until the desired magnification appears adjacent to the power index dot (Fig. 2).

3. Adjustment of the riflescope

Sighting through the riflescope, align the rifle with your aiming point on the target and shoot a trial round. If the bullet does not hit the

aiming point, adjust the elevation and windage after removing the Adjustment cap, as follows:

4-12X42

蘆For the Laser IRT adjustment is made by turning the grip by hand. If the bullet hits under the aiming point, turn the grip in the direction of

the arrow marked "U". If the bullet hits to the left of the aiming point, turn the grip in the direction of the arrow marked "R" (Fig. 12).

Note:

蘆The windage and elevation scales of the Laser IRT 4-12X42 is calibrated in divisions of 1/4 minute of angle with a click at intervals of 1/4

minute of angle (half division).

蘆When adjusting the reticle to the point of aim, remember that one minute of angle equals approximately one inch (2.54 cm) at 100 yards

(91.44 m). Therefore, if the impact point is two inches (5.08 cm) low and one inch (2.54 cm) right at 100 yards (91.44 m) Parallax Setting,

you should adjust two minutes of angle up one minute of angle left.

Laser Range Finder

Caution - use of controls or adjustments or performance of procedures other than those specified herein may result in haz-

ardous radiation exposure

1. Install a battery in the battery chamber. (See "Changing Batteries")

2. Diopter adjustment

Refer to Riflescope Diopter ajustment.

Depress POWER or REMOTE

control button over 2 seconds

until the display changes

START

− C −

Depress Remote

control button

Depress

Power button

Align the reticle cross

and Target

Measurement

"Distance" or "

−−−

(Success or Failure)

Over

12 seconds

Over

8 seconds

Measurement

"Distance" or "

−−−

(Success or Failure)

Stand-by mode *

Power OFF **

Over

2 hours

Over

2 hours

Stand-by mode *

Power OFF **

Over

8 seconds

Repeat

action

another

target

same

target

No No

Change to Measurement mode

START

Depress Remote

control button

Depress

Power button

Align the reticle cross

and Target

Depress Remote

control button

Depress

Power button

− O −

(

Display on seven segment

)

(

Operation of Unit

)

(

Action of Unit

)

Normal (continuous) measurement mode ONE SHOT measurement mode

3. Measuring

Eyepiece Adjustment

Eye Relief

Fig. 9

Fig. 12

4. Selecting measurement mode

蘆Continuous measurement

The instrument continuously measures distance for 12 seconds.

Depress POWER or REMOTE

control button over 2 seconds

until the display changes

Normal

(continuous)

measurement

mode

One shot

measurement

mode

Change to Measurement mode

Specifications

★ When maximum magnification (12x) is selected.

* (at minimum magnification) - (at maximum magnification)

** moa = minute of angle

***The battery chamber is water resistant, not waterproof. Water may enter the device if the laser IRT is submerged in water. If water enters the

battery chamber, wipe out any moisture and allow time for the chamber to dry.

●Waterproof models:

The Laser IRT is waterproof, and will suffer no damage to the optical system if submerged or dropped in water to a maximum depth of 2 meters

for up to 5 minutes.

The Laser IRT offers following advantages:

蘆Can be used in conditions of high humidity, dust and rain without risk of damage.

蘆Nitrogen-filled design makes it resistant to condensation and mold.

Observe the following when using the Laser IRT:

蘆As the unit does not have a perfectly sealed structure, it should not be operated nor held in running water.

蘆Any moisture should be wiped off before adjusting movable parts (Power selector Ring, eyepiece, etc.) of the Laser IRT to prevent damage and

for safety reasons.

To keep your Laser IRT in excellent condition, Nikon Vision recommends regular servicing by an authorized dealer.

Troubleshooting/Repair

If your Nikon Laser IRT should require repair, please contact your local dealer for details regarding where to send it. Before doing so, you are

advised to consult the Troubleshooting Table below.

Check Points

蘆Depress POWER button.

蘆Check and replace battery if necessary.

蘆Be sure that nothing, such as your hand or finger, is blocking the laser emission aperture

and laser detector.

蘆Be sure that the laser emission aperture and laser detector are clean. Clean them if neces-

sary.

蘆Be sure that the target shape and condition is appropriate to reflect the laser beam.

蘆Replace battery.

蘆Be sure to hold the unit steady while depressing the POWER button.

蘆Be sure the target is within measuring range (33-766 yards)

蘆Be sure that nothing, such as leaves or grass, is between the Laser IRT and the target.

蘆Replace battery.

蘆Be sure that the target shape and condition is appropriate to reflect the laser beam.

蘆Be sure to hold the unit steady while measuring the distant.

蘆 Be sure that nothing, such as leaves or grass, is between the Laser IRT and the target.

蘆Replace battery.

蘆Be sure that the target shape and condition is appropriate to reflect the laser beam.

蘆Be sure that nothing, such as leaves or grass, is between the Laser IRT and the target.

Symptom

Unit does not turn on - LED fails to illumi-

nate

Target range cannot be obtained

[

−−−

] ("Cannot measure") appears

Closer target cannot be measured

Target beyond a certain distance cannot

be measured

Measurement result is unstable

Incorrect result is displayed

4-12x42

4x-12x

1.65

3.5★

0.14★

74-75

2.9-3.0

7.6-2.5

25.0-8.2

2.05

330

700

24.7

1/4: 1 click

91.44

100

1.78

FDA Class I

905nm

26ns

0.036 degree

33-766 yards

1 yard step

Scope: Waterproof (maximum depth of 2 meters for up to 5 minutes),

Battery chamber: Water resistant ***

−10°to ＋50°

Attachable to a gun with Velcro

Scope: 3 volts DC, CR-2 lithium battery x1

Remote control unit: 3 volts DC, CR2025 lithium battery x1

21 CRF PART 1040.10: 1985

FCC Part 15/Sub Part B Class B

MODEL

SCOPE

Actual magnification

Objective diameter (mm)

(in)

Exit pupil (mm)

(in)

Eye relief (mm)

* (in)

Field of view at 100 yds. (m)

* (ft)

Objective outside diameter (mm)

(in)

Length (mm)

(in)

Weight (g)

(oz)

Adjustment graduation **

(moa)

Maxinum internal adjustment **

(Elevation & Windage) (moa)

Parallax setting (m)

(at factory) (yards)

Outside Diameter of (mm)

Eyepiece (in)

Laser

Class

Wavelength

Pulse duration

Output

Beam Divergence

Others

Measuring range

Distance display

Structure

Operating temperature

Remote control unit

Power source

Safety & EMC

If problems persist after consulting the Troubleshooting Table, please contact your local dealer to check/repair the Laser IRT. Never let anyone

other than the official representative of the product manufacturer check or repair the Laser IRT. Failure to follow this instruction could result in

injury, or damage to the product.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired opera-

tion.

Do not use the Laser IRT for purposes beyond the limits of its stated accuracy.

Stand-by mode * Unit accepts operation with Remote control unit.

Power OFF ** Unit does not accept operation with Remote control unit.

At Power OFF mode, before using the Remote control unit Power switch must be depressed.

Nikoplex Reticle

Fig. 10

BDC Reticle

Fig. 11

ITEM SUPPLIED

Body

...................................................

1pc.

Eyepiece cap

Objective cap

..............................

1pair

Battery (CR2 & CR2025)

............

1pc. each

Hood

..............................................

Option

1 2

Kommentare zu diesen Handbüchern

Keine Kommentare

Nikon Laser IRT Bedienungsanleitung Seite 2

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Entfernungsmesser Nikon Laser IRT