Nikon ACULON Bedienungsanleitung Seite 37
- Seite / 64
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
43
En
Fr
Es
Pt
Mesure
Attention — L'emploi de commandes, réglages ou
performances de procédure autres que ceux
spécifiés dans ce manuel peut entraîner une
exposition à des rayonnements dangereux.
1. Installez une pile dans le logement prévu à cet
effet. (Reportez-vous à la section « Insérer et
remplacer la pile »).
2. Correction dioptrique
Réglez la correction dioptrique pour obtenir une
image nette sur l'écran ACL.
Tournez d'abord la bague de réglage dioptrique dans
le sens antihoraire jusqu'à ce qu'elle soit totalement
en butée. Ensuite, mettez l'appareil sous tension
pour activer l'écran ACL quand vous regardez dans le
Télémètre Laser Nikon. Tournez la bague de réglage
dioptrique dans le sens horaire jusqu'à ce que
l'affichage soit net.
Si la correction dioptrique ne correspond pas à votre
vue, vous aurez des difficultés à effectuer la mise au
point sur le sujet.
3. Mesure
Avant de prendre les mesures, veillez à confirmer les
paramètres du dispositif.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
- (lithium battery) 2
- (Monocular) 2
- SAFETY PRECAUTIONS 2
- Internal display 6
- Distance display units 8
- Target priority mode 8
- Specifications 10
- Troubleshooting/Repair 11
- PRECAUCIONES DE SEGURIDAD 15
- Precauciones antes del uso 16
- CUIDADO Y MANTENIMIENTO 17
- Características clave 18
- Nomenclatura/Componentes 19
- Componentes 19
- Pantalla interna 21
- Medición 22
- Modo de prioridad al sujeto 23
- Especificaciones 24
- Français 28
- Précautions avant utilisation 30
- PRECAUTIONS DE SECURITE 31
- (Pile au lithium) 31
- PRÉCAUTIONS DE SÉCURITÉ 31
- (Objectif monoculaire) 31
- Caractéristiques principales 33
- Nomenclature/Composition 34
- Composition 34
- Insérer et remplacer la pile 35
- Écran interne 36
- Measurement 37
- Spécifications 38
- Symptômes Points à vérifier 40
- Português brasileiro 42
- PRECAUÇÕES DE SEGURANÇA 44
- Cuidados antes do uso 45
- CUIDADOS E MANUTENÇÃO 46
- Principais características 47
- Nomenclatura/Composição 48
- Composição 48
- Inserção e troca de pilhas 49
- Visor interno 50
- Modo de prioridade de alvo 52
- Especificações 53
- Problemas e Soluções/Reparo 55
- Sintoma Pontos a Verificar 56
- NIKON VISION CO., LTD 57
Verwandte Produkte und Handbücher für Entfernungsmesser Nikon ACULON
(44 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.143 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern