Nikon DSR-1500AP Bedienungsanleitung PDF herunterladen (Seite 47)

Setting the Time Data

Chapter 3 Convenient Functions for Editing Operation

2 Set the TIME CODE menu items (see page 63) as

shown below.

3 Press the TC PRESET button in the menu control

section.

The current setting is shown on the monitor screen and

in the time counter display on the front panel. The

leftmost digit keeps flashing.

One of the following menu screens is displayed on the

monitor depending on the setting made in step 1

Note

If you press the TC PRESET button while CNT value

is being displayed, the message “COUNTER MODE

IS SELECTED.” will appear on the monitor screen

and “CNT mode!” will appear in the time counter

display on the front panel. If this happens, press the

COUNTER SELECT button to light the time data type

indicator “TC” or “U-BIT.”

4 Use the g and G buttons to move the flashing digit to

the value to be changed.

5 Use the f and F buttons to change the value of the

flashing digit.

Enter hexadecimal values (0 to 9, A to F) when setting

user bit data.

6 Repeat steps 4 and 5 until you have set the desired

values for all digits.

To set a value of 00:00:00:00, simply press the RESET

(NO) button.

7 Press the SET (YES) button.

The message “NOW SAVING...” appears on the

monitor screen, “Saving...” appears in the time counter

display, and the new settings are stored in memory.

After this saving operation is completed, the monitor

screen and the time counter display return to their

usual status.

Note

The set data may be lost if you power off the unit while

the above saving operation is in progress. Wait until

the saving operation is completed before powering off.

Advancement of internal time code

generator

The internal time code generator can advance in either of

two modes, which can be set with the RUN MODE menu

item (see page 63).

FREE RUN: Advancement starts when the data saving

operation is completed.

REC RUN: Advancement starts when recording starts and

stops when recording stops.

To set the current time as the initial time

code value

In step 2 above, set the RUN MODE menu item to FREE

RUN, then set the current time (format: HH:MM:SS:FF =

hours: minutes:seconds:frame number) in step 3 and

subsequent steps.

Synchronizing Internal and External

Time Codes

The internal time code generator can be synchronized with

an external time code (LTC) input to this unit.

To synchronize the internal time code to

external time code

Input an external time code (LTC) signal to the TC IN

connector, then set the TC MODE menu item (see page

63) to EXT REGEN.

The internal time code generator locks onto the external

time code and starts advancing. Once the internal time

code generator has been synchronized in this way, you can

disconnect the external time code input and this unit will

maintain the synchronized time code.

Note

When the selected input mode is “SDTI” or “i.LINK” (the

SDTI or i.LINK indicator is lit in the INPUT signal display

section), setting the TC MODE menu item to EXT

REGEN causes the internal time code generator to

Menu item Setting

TC MODE “INT PRESET”

RUN MODE “FREE RUN” or “REC RUN”

DF MODE

(for DSR-1500A only)

Normally “ON (DF)”

TC PRESET MODE

TCG 00:00:00:00

INC/DEC : ( )( )KEY

SHIFT : ( )( )KEY

CLEAR : RESET KEY

DATA SAVE : SET KEY

ABORT : TC PRESET KEY

UB PRESET MODE

UBG 00:00:00:00

INC/DEC : ( )( )KEY

SHIFT : ( )( )KEY

CLEAR : RESET KEY

DATA SAVE : SET KEY

ABORT : TC PRESET KEY

Initial time code value setting

screen

User bit setting screen

1 2 ... 42 43 44 45 46 47 48 49 50 51 52 ... 111 112

Kommentare zu diesen Handbüchern

Keine Kommentare

Nikon DSR-1500AP Bedienungsanleitung Seite 47

Kommentare zu diesen Handbüchern