Nikon DX-TL4516E Bedienungsanleitung PDF herunterladen (Seite 19)

Basic operations

ENGLISH

Copying the recorded data

This item is used to copy the data from the main device to a

copy device.

Copy Data to Copy 1 Drive/Set Copy 1 Drive

This item is used to copy the data to Copy 1 device by speci-

fying the start and end points. The points are specified by

the date and time or the bookmark. This function is useful for

copying the data of the short period of time.

Before executing the copy, make sure that the Copy 1

device is connected and set in the <Add/Remove HDD

Device> and <Add/Remove DVD/CD Drive> correctly.

(System Menu Memory)

1 + 2

Copy

steps

1, 2

step

steps

4, 5

Copy Data to Copy 1 Drive

Set Copy 1 Drive

Range of Copy

User Menu

step

1. Set the camera number to be copied.

• The button function changes between “All Off”

and “All On” each time you select this button.

You can switch on and off for all the cameras

easily by using this button.

• The picture is not copied when there is no

recorded picture of the set camera number or

time. Make sure to check that the picture of the

specified camera has been recorded on the

speciﬁed copy start point.

step

2. Select “Other settings” and then set the detailed

settings.

From Device: Sets the device which contains the

data to be copied. The available setting items are

“Main” and “Copy 2.”

From Group: Sets the group which contains the

data to be copied. The available setting items are

“Normal,” “Alarm,” and “LPA” for main, “SerialBus,”

“DVD/CD,” and “Internal” for copy 2.

To Copy 1: Sets the group to where the data is

copied. The available setting items are “SerialBus,”

“DVD/CD,” and “USBmemory.”

Copy Data: Sets the data area to be copied. The

available setting items are “Alarm” and “All.”

Overwrite: Selects whether or not to overwrite the

existed data.

Auto Eject: Selects whether to eject media (CD/

DVD) automatically when the copy is over.

“Alarm” appears for “From Group” when “Alarm Recording

Area” is set to other than “0 %.” (System Menu Memory

Data Management Setting for Main Memory)

“LPA” appears for “From Group” when “Long Pre-Alarm

Area” is set to other than “0 %.” (System Menu Memory

Data Management Setting for Main Memory)

When copying the data to DVD while “Overwrite” is set to

“On,” the unit clears the existing data on the disc before

overwriting with new data. Note that clearing the data

takes about 30 to 40 minutes. You cannot cancel opera

tion during clearing the data of the DVD.

When copying the data while “Copy Data” is set to “Alarm,”

the unit performs copy operation, however, the data is not

copied if there is no alarm recording data within the speci-

ﬁed range of copy. In case of CD/DVD disc, the remaining

capacity becomes low because only the management

information is recorded. It is recommended to carry out

“Calculate” in <Copy Data to Copy 1 Drive> to confirm

whether or not there is alarm recording data in the speci

ﬁed range.

step

3. Set the start, start/end, or end point of copy by

specifying the date and time or the bookmark

number.

Start: Sets only the start point of copy. The data

is copied from the specified start point as much

data as possible with the remaining capacity of the

media to be copied.

Start/End: Sets the start and end points of copy.

End: Sets only the end point of copy. The data

is copied as much data as possible with the

remaining capacity of the media to be copied until

the speciﬁed end point reaches.

• To set the bookmark point, select “Bookmark”

and then select the desired bookmark number.

• To copy from the oldest recording time, select

“Co py Sta r t Ti me. ” To c opy to t he lat e st

recording time, select “Copy End Time.”

step

4. Select “Calculate” to calculate the capacity of data

to be copied.

When using “End,” the copy cannot be executed unless

the calculation of the capacity of data to be copied is com-

pleted.

When using “Start” or “Start/End” and executing copy

without calculating the capacity of data to be copied, the

progress or the time of the copy may not be displayed

correctly because the unit cannot determine the capacity

of data to be copied.

step

5. Select “Execute.”

• The copy starts.

• To stop copy manually, select “Cancel” in the

progress screen. The data which has been

copied before cancelling is copied.

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 36 37

Kommentare zu diesen Handbüchern

Keine Kommentare

Nikon DX-TL4516E Bedienungsanleitung Seite 19

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Auto DVR Nikon DX-TL4516E